OKX Wallet

List of the table of contents of this article:

• 1,< A href='#What should I do if the notebook can't enter the system?' title='What if the laptop can't enter the system?' > What should I do if the laptop can't enter the system?
• 2, The laptop can't enter the system when it is turned on, what should I do
• 3、What should I do if the laptop can't be turned on
• 4, The laptop can't enter the system?

What should I do if the laptop can't enter the system?

Modify the boot order: If the computer cannot recognize the hard disk at startup, we can enter the BIOS interface, modify the boot order, and put the hard disk at the top of the device list. In this way, the computer can start the system normally. Check for hardware problems: If there is a problem with the hardware inside the computer, it may need to be replaced or repaired.

One, enter the safe mode and remove the recently installed driver/software. 1 Boot to WinRE (Windows Recovery Environment), which can be understood as recovery mode.You can press the power-on button for a long time until the machine is power-off, then turn it on, and then turn off the power, repeat 3-5 times until you enter the recovery mode as shown in the figure below.

Try to enter the safe mode debugging, press the power button to shut down the system for a long time, and repeat about 3 times; click the "Troubleshoot" option, then click "Advanced Options", click "Restart" under "Start Settings", and select "Safe Mode" after restarting.

Solution: If you are sure that this is the case, you just need to pull out the problematic parts, replace them with new ones or clean up the dust.

The reasons why Dell notebooks can't start and enter the system are: power failure, system crash, hardware failure, startup item setting error, and virus infection. Power failure: Problems with the power supply of Dell notebooks may cause failure to start.You can try to replace the power cord, reset the power supply, or check whether the power supply is working properly.

The laptop can't enter the system when it is turned on, what should I do

Press the power button to turn off the system for a long time, repeat about 3 times; click the "Troubleshoot" option, and then click "Advanced Options" ", click "Restart" under "Startup Settings", and select "Safe Mode" after restarting. 3. Difficulty Solving - Initialize the computer. Third, the software debugging is invalid. It is recommended to go to the after-sales inspection of the hardware.

You can press the power-on button for a long time until the machine is out of power, then turn it on, and then turn off the power, repeat 3-5 times until you enter the recovery mode shown in the figure below. 2 From the selection screen, click orClick to solve the problem

System file damage If the Windows system file is damaged, the computer may have repeated startup problems. You can try to use the Windows installation disk or the system recovery partition to repair it.

What should I do if the laptop can't be turned on and can't enter the system

You can press the power button for a long time until the machine is power off, then turn it on, and then turn off the power again, repeat 3-5 times until it enters the recovery mode shown in the figure below. 2 From the selection option screen, click or click the difficult solution

Press the power key to turn off the power for a long time to enter the system, and repeat about 3 times; click the "Triddle Solution" option, then click "Advanced Options", click "Restart" under "Start Settings", and select "Safe Mode" after restarting.3. Difficulty Solving - Initialize the computer. Third, the software debugging is invalid. It is recommended to go to the after-sales inspection of the hardware.

Sometimes when the computer cannot enter the system is turned on, it is generally caused by software or hardware failure. There are many and complex reasons. It may be system file damage, virus infection, or graphics card or memory problems.

You can enter the "safe mode" for antivirus. You can check the "BIOS" of the laptop to see if there is an error in reading, writing and damage. Reinstalling the system" is also a quick way to solve the problem that the computer cannot enter the system when it is turned on.

The laptop can't enter the system?

Virus destruction, first kill the virus and then repair, caused by illegal shutdownDamage, directly repair the bad channel of the hard disk, which cannot be repaired. An installed program destroys the system file, uninstall and then repair it. Repair method: Press F8 when you turn it on until the advanced option appears, and select "The latest correct configuration" to return to repair.

Power supply problem If it is an external power supply, first check whether the power supply is not checked or there is a problem with the plug. If you use a battery, it may be that the battery is insufficient. You can charge more before use to solve this problem. Motherboard failure. Motherboard failure will also cause the computer to fail to turn on.

The laptop cannot enter the system desktop when it is turned on, which is generally caused by: damage to the system file, aging or poor contact of the internal line of the computer, and problems with the graphics card. System file damage If the Windows system file is damaged, the computer may start up repeatedly.

The reasons why Dell notebooks can't start and enter the system are: power failure, system crash, hardware failure, startup item setting error, and virus infection. Power failure: Problems with the power supply of Dell notebooks may cause failure to start. You can try to replace the power cord, reset the power supply, or check whether the power supply is working properly.

There are many reasons why the laptop cannot enter the system, which may be a software problem or a hardware problem. This article will introduce the reasons why laptops cannot enter the system from the two aspects of software and hardware. Software problems. In terms of software, system damage may lead to the inability to access the system. Just reinstall the system to solve the problem.

3 Please click or click on the advanced options and select [Startup Settings],. SelectSelect [Start] and click the safe mode environment you want to enter. In general, it is recommended to select (4) to enable the safe mode. Second, using the automatic repair function can detect and solve some system problems to prevent Windows from starting.